RAPIDMIXPortable 3 Bin Cold Feed System

SPECS:
Large 14' x 9'-6" Hopper bins
30" wide 5 HP feeder conveyor
36" wide 10 HP collecting conveyor
Portable chassis and hopper support structure of heavy duty W-flange beam

SET-UP FOOTPRINT:
10' wide
59'-6" long
14' height
height of collection conveyor clearance, once set up is: 5'5"

LOGISTICS INFO:
Width: 10'
King pin to rear axle is: 44'-6"
Entire length is: 57’-6"
Weight-Unknown

Each hopper is 9’-6” wide x 14’ long with 20 tons storage capacity constructed from 1/4” thick
steel plate with rectangle tube reinforcing at the hopper top and angle iron reinforcing at the
hopper mid-section and bottom section; self-relieving tapered hopper bottom opening to
minimize bridging; full length skirt boards with Rema Skirt 50 adjustable rubber flashing to
prevent leakage between hopper bottom and belt feeder; adjustable discharge gate with hand
crank to control material flow from each hopper.

Each belt feeder is 30” wide x 8’ long with fixed speed 5 h.p. electric motor, Dodge TXT425 shaft
mount speed reducer, v-belt drive and OSHA drive guard; Dodge 12” diameter rubber lagged
head pulley mounted on Dodge 2-7/16” SCM pillow block bearings; Dodge 12” diameter self-
cleaning tail pulley mounted on Dodge 1-15/16” SCM pillow block bearings; screw take-up
assemblies; OSHA tail terminal guard and side nip guards; ICC CEMA “C” flat belt idlers with 5”
diameter rolls mounted on close centers; 3 ply vulcanized endless conveyor belting. Belt speed
setup for 90 fpm.

Collecting conveyor is 36” wide with fixed speed 10 h.p. electric motor, Dodge TXT315 shaft
mount speed reducer, v-belt drive and OSHA drive guard; Dodge 12” diameter rubber lagged
head pulley mounted on Dodge 2-3/16” SCM pillow block bearings; Dodge 12” diameter self-
cleaning tail pulley mounted on Dodge 1-15/16” pillow block bearings; screw take-up
assemblies; OSHA tail terminal guard; head pulley nip guards; ICC CEMA “C” 35 degree troughing
idlers with 5” diameter rolls; ICC CEMA “C” return idlers with 5” diameter rolls; 2 ply conveyor
belting with 3/16” x 1/16” rubber covers; Flexco 140 mechanical belt splice; 9’-6” long conveyor
extension beyond the hoppers which folds for transport.

Portable trailer constructed of heavy duty wide flange beams which are braced for optimum
rigidity; wide flange vertical beams and angle iron cross members tie all hoppers and trailer
together; single axle chassis with dual 11 x 22.5 tires, air brakes, king pin, rear lighting, mud flaps
and blocking pads.

One rust inhibitor prime coat and one finish coat gray paint for all equipment; one finish coat
safety yellow paint for all guarding.

Electric motor control panel with main disconnect, AC Tech SMV variable speed drives for the
belt feeders, branch circuit protection, fixed speed starter for the collecting conveyor, all
mounted on a skid support structure bolted to the trailer frame and wired into the electric
motors.

CALIBRATION - The discharge gates can be adjusted to control the depth of bed of material coming out of the
hopper and the variable speed drives change the belt speed of each belt feeder.

Head terminal includes Weg 15 h.p. TEFC electric motor; Dodge TXT4 shaft mount speed reducer
with internal backstop; v-belt drive and OSHA approved drive guard; Dodge 14" diameter rubber
lagged head pulley mounted on 2-7/16" diameter 1045TGP shafting with Dodge SCM pillow
block bearings; head pulley nip guards.

Tail terminal includes Dodge 12" diameter self-cleaning tail pulley mounted on 2-3/16" diameter
1045TGP shafting with Dodge SCM pillow block bearings; screw take-up assemblies; OSHA
approved tail terminal guard.

Standard 5' long receiving hopper with skirt boards, rubber flashing and bolt-on wing
attachments.

Conveyor frame constructed of 8" channel iron with 2" square tube reinforcement making a
rigid framework which is easily stacked for hauling.

Conveyor belting, 2 ply, with 3/16" top rubber cover and 1/16" bottom rubber cover; Flexco 140
mechanical belt splice.  36”

CEMA "C" conveyor troughing idlers 35 degree deep with 5" diameter rolls mounted on 4'
centers; CEMA "C" troughing idlers 20 degree deep with 5" diameter rolls mounted on close
centers at the load point; CEMA "C" return idlers with 5" diameter rolls mounted on 10' centers.

Adjustable height V-style support legs for stockpiling.

SOLD AS-IS WHERE-IS WITH NO IMPLIED WARRANTY.

Production range150 Tons Per Hour
Price from$170,000.00

Product Images

Get a quote

Thank you for your interest in the equipment and services of DHE Inc. Let our staff know exactly what your needs are, and we will be happy to contact you with a quote to discuss how we can best meet your project specifications. 

Fullname
Email
Phone
Company
Location
Message
Captcha